Baked Oak is a warm rich dark brown tone, as opposed to the usual honeyed hue. The colouring is consistent throughout the entire layer of oak, so unlike a dark lacquer or oil, the dark tones won’t be affected by scratches or re-sanding. As the name suggests, only temperature is involved in this treatment. No chemicals are used to achieve this effect.
Our engineered wood flooring meets modern requirements and keeps a traditional wood flooring appearance. The multiple layers of plywood backing give support to the visible top layer of the precious hardwood, resulting in a floor that looks and feels like a solid wood floor but that is suitable for under floor heating, can be laid over almost all types of sub floor, and can still be sanded and re-finished after years of use.
Oil finishes penetrate into the wood to protect the timber and in doing so, enhance the grain. This adds depth to the wood's natural appearance in the process. Oiled finishes are very popular as they have a natural look and feel, so simply add to the appearance of the wood.
The warm and rich tone of the wood is emphasised by the finish, which has no added colouring.
Under Floor Heating
£73.33 / m2 + VAT
We recommend adding 7-10% m2 to the total area for board or strip floors, or 10-15% for parquet.
Enter your details to calculate your meterage and cost.
Our engineered board has been produced using a Russian WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.
The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.
Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The board is supplied with a micro bevel along the length of the board, factory Oiled ready to use
*if the product is being laid in a high traffic environment then an additional coat of oil is recommended.
Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production.
Type of Finish: Pre-oiled - An additional coat of oil is recommended.
Profile: Tongue and Groove
Specification: Bevelled Edge
Unit Weight: 15kg
Size: 180 x 20 mm
Width: 180 mm
Thickness: 20 mm
Suitable for underfloor heating: Yes
Under Floor Heating
See fitting information
Under Floor Heating
This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.
2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Russian Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.
Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.
This product is supplied with a Factory UV Oiled surface. The Natural Wood Floor Company recommends that an additional coat of oil is applied to the surface prior to regular use.
A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.
Nail fixing is usually done via a nail gun, e.g Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.
Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.