Oak Baked Unsealed 210 x 20 mm 3.4m2

This product is no longer available

Engineered Flooring 210 mm x 20 mm

A SET SQUARE METERAGE AT A FIXED PRICE

THERE IS ONLY ONE JOBLOT OF 3.4m2 OF THIS PRODUCT!

Was £255.00 Now £153.00 Excluding VAT

Our Baked Oak Unsealed engineered oak flooring meets modern requirements and keeps a traditional wood flooring appearance. The multiple layers of plywood backing give support to the visible top layer of the precious hardwood, resulting in a floor that looks and feels like a solid wood floor but that is suitable for under floor heating, can be laid over almost all types of sub floor, and can still be sanded and re-finished after years of use.

The versatile nature of Oak means this floor is perfect for all kinds of design scheme. From more traditional, natural looking styles to more contemporary, coloured finishes, Oak can be tailored to your preference.

Baked Oak is a warm rich dark brown tone, as opposed to the usual honeyed hue. The colouring is consistent throughout the entire layer of oak, so unlike a dark lacquer or oil, the dark tones won’t be affected by scratches or re-sanding.
We recommend adding 7-10% m2 to the total area for board or strip floors, or 10-15% for parquet.

Enter your details to calculate your meterage and cost.



Floor Size: 0m2


Packs: Variable pack size

£45.00 / m2 + VAT

Product codeJOB/1837

This product is no longer available. Please contact us for further information.

020 8871 9771

Our engineered board has been produced using a Russian WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.

The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.

Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The unsealed board is supplied with a micro bevel along the length of the board, pre- sanded requiring only a light 100/120 grit sand to finish.

Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production

Product code: JOB/1837

Grade: Millrun

Species: Oak

Group: Engineered Flooring

Category: Joblot


Type of Finish: Unsealed

Brushed: No

Profile: Tongue and Groove

Specification: Bevelled Edge

Unit Weight: 14.5kg

Pack size: 3.4

Size: 210 x 20 mm

Width: 210 mm

Thickness: 20 mm


Nail Fitting: Nail fixing is usually done via a nail gun, e.g Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.

Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.

Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.

Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.

Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Russian Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.

Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.


Have no product in the cart!
0