Oak Coastal Grey Oiled 180 x 15 mm

Engineered Flooring 180 mm x 15 mm

The beauty of Coastal Grey is that it combines the fashionable shade of grey with warm sandy tones and a weathered, textured surface. The grey coloured oil adds interest by picking up the wood's distinctive grain patterns and rustic knots, creating a look that’s subtle enough to go with all décor schemes.

This is a versatile floor that will go with almost anything. There’s lots of variation with the colour and grain patterns, so this is a floor that you will never tire of. It will just get better and better over time.

This engineered oak overlay floor can only be laid over an existing subfloor, not as a structural floor. Overlays are made up of a top layer of precious hardwood with a multi-layer ply backing, meaning this floor has the same beautiful appearance of solid wood but is a much more efficient and sustainable use of material.

£52.50 / m2 + VAT

Product codeOLOCGO/180

Order a sample
We recommend adding 7-10% m2 to the total area for board or strip floors, or 10-15% for parquet.

Enter your details to calculate your meterage and cost.



Floor Size: 0m2


Packs: Variable pack size

Our engineered board has been produced using a Russian WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.

The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.

Suitable for secret fixing to a ply subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The board is supplied with a micro bevel along the length of the board, factory Oiled ready to use.
*if the product is being laid in a high traffic environment then an additional coat of oil is recommended.

Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor.

Product code: OLOCGO/180

Grade: Millrun Grade, contains knots & Colour variation

Species: Oak

Group: Engineered Flooring

Category: Engineered Overlay


Type of Finish: Oiled - An additional coat is recommended.

Brushed: No

Profile: Tongue and Groove

Specification: Bevelled Edge

Unit Weight: 11kg

Size: 180 x 15 mm

Width: 180 mm

Thickness: 15 mm


Suitable for underfloor heating: Yes

Nail Fitting Nail fixing is usually done via a nail gun, e.g Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.

Stick Down Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.

Floating A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.

Under Floor Heating

Engineered 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Russian Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.

Micro Bevelled Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.

Pre-Oiled This product is supplied with a Factory UV Oiled surface. The Natural Wood Floor Company recommends that an additional coat of oil is applied to the surface prior to regular use.


Have no product in the cart!
0