Engineered Flooring 210 × 20 mm
The rich red-brown tone of our Cognac oiled floor accentuates the intricate patterns and golden tones of the Oak itself, creating a beautiful and impressionable floor.
Oak is a versatile species that takes pigments very well, so it lends itself well to pre-sealed flooring. The physical characteristics that give Oak its charm are still visible through the finish, so this floor has a naturally charming character and can be matched with the desired design scheme.
Oil finishes penetrate into the wood to protect the timber and in doing so, enhance the grain. This adds depth to the wood’s natural appearance in the process.
The ply backing of an engineered floor with a hardwood veneer glued on top gives our engineered floors the same beautiful appearance of a solid wood floor but with superior construction, greater stability, and compatibility with under floor heating.
The wide board format is perfect for large open spaces, as generous room proportions will enhance the quality and splendour of this floor’s gorgeous finish.
Enter your details to calculate your meterage and cost.
Floor Size: 0m2
Packs: Variable pack size
Our engineered board has been produced using a Russian WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.
The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.
Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The board is supplied with a micro bevel along the length of the board, factory Oiled ready to use
*if the product is being laid in a high traffic environment then an additional coat of oil is recommended.
Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production.
Product code: OLCO/210
Type of finish: Engineered Pre-Oiled
Brushed: Millrun Grade, contains knots & Colour variation
Profile: Oiled – An additional coat is recommended.
Weight: 15 kg
Recommended Use: per Square Metre
Dimensions: 210 × 20 mm
Width: 210 mm
Thickness: 20 mm
Colour : Dark
Under Floor Heating : Tongue and Groove
Unit Measurement : Bevelled Edge
Design : Wide Boards (150mm – 300mm), Engineered
Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Russian Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.
Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.
Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.
Nail Fitting: Nail fixing is usually done via a nail gun, e.g. Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.
Pre-Oiled: This product is supplied with a Factory UV Oiled surface. The Natural Wood Floor Company recommends that an additional coat of oil is applied to the surface prior to regular use.
Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.
Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.