Flooring 160 × 15 mm
£68.50 / m2 incl. VAT
A fantastic floor for those who prefer a less intense white than the Pure White boards.
These 160 mm boards combine the best characteristics that oak has to offer, with a simple white wash effect.
The result is a striking visual effect, which can either act as a backdrop for more vivid colours or become a focal point in more refined and simple decorating schemes.
Enter your details to calculate your meterage and cost.
Floor Size: 0m2
Extra Margin: 10%
Total Area Required:
This product can only be purchased in whole packs
Packs: Variable pack size
Our engineered board has been produced using WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.
The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.
Suitable for secret fixing to a ply subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The board is supplied with a micro bevel along the length of the board, factory Oiled ready to use.
*if the product is being laid in a high traffic environment then an additional coat of oil is recommended.
Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor.
Product code: OLOWF/160
Species: Oak
Finish: Lacquered
Brushed: Light
Profile: Tongue and Groove
Specification: Bevelled Edge
Weight: 10 kg
Recommended Use: Domestic and Light Commercial
Dimensions: 160 × 15 mm
Width: 160 mm
Thickness: 15 mm
Colour : Light
Type of finish : Lacquered
Under Floor Heating : Yes
Unit Measurement : per Square Metre
Design : 15mm Boards, Engineered
Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Birch Plywood. Boards can be Nailed, Stuck Down, or Floated depending on product type and sub floor. Parquet woodblocks must be stuck down. All floors are Tongue and Groove with Ends Matched unless stated otherwise.
Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.
Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.
Nail Fitting: Nail fixing is usually done via a nail gun, e.g. Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.
Pre-Lacquered: This product is supplied with a Factory UV Lacquered surface. This product is suitable to walk on immediately.
Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.
Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.
See fitting information
Engineered
2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Birch Plywood. Boards can be Nailed, Stuck Down, or Floated depending on product type and sub floor. Parquet woodblocks must be stuck down. All floors are Tongue and Groove with Ends Matched unless stated otherwise.
Floating
A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.
Micro Bevelled
Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.
Nail Fitting
Nail fixing is usually done via a nail gun, e.g. Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.
Pre-Lacquered
This product is supplied with a Factory UV Lacquered surface. This product is suitable to walk on immediately.
Stick Down
Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.
Under Floor Heating
This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.