Flooring 210 × 20 mm
The beauty of Coastal Grey is that it combines the fashionable shade of grey with warm sandy tones and a weathered, textured surface. The grey coloured oil adds interest by picking up the wood’s distinctive grain patterns and rustic knots, creating a look that’s subtle enough to go with all décor schemes.
This is a versatile floor that will go with almost anything. There’s lots of variation with the colour and grain patterns, so this is a floor that you will never tire of. It will just get better and better over time.
Oak is a versatile species that takes pigments very well, so it lends itself well to pre-sealed flooring. The physical characteristics that give Oak its charm are still visible through the finish, so this floor has a naturally charming character and can be matched with the desired design scheme.
Our engineered wood flooring meets modern requirements and keeps a traditional wood flooring appearance. The multiple layers of plywood backing give support to the visible top layer of the precious hardwood, resulting in a floor that looks and feels like a solid wood floor but that is suitable for under floor heating, can be laid over almost all types of sub floor, and can still be sanded and re-finished after years of use.
The wide board format is perfect for large open spaces, as generous room proportions will enhance the quality and splendour of this floor’s gorgeous finish.
Enter your details to calculate your meterage and cost.
Floor Size: 0m2
Extra Margin: 10%
Total Area Required:
This product can only be purchased in whole packs
Packs: Variable pack size
Our engineered board has been produced using WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.
The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.
Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The board is supplied with a micro bevel along the length of the board, factory Oiled ready to use
*if the product is being laid in a high traffic environment then an additional coat of oil is recommended.
Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production.
Product code: OLCGO/210
Species: Oak
Finish: Oiled
Brushed: No
Profile: Tongue and Groove
Specification: Bevelled Edge
Weight: 14.3 kg
Recommended Use: Domestic and Light Commercial
Dimensions: 210 × 20 mm
Width: 210 mm
Thickness: 20 mm
Colour : Light
Type of finish : Oiled – An additional coat is recommended.
Under Floor Heating : Yes
Unit Measurement : per Square Metre
Design : 20mm Boards, Engineered
Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Birch Plywood. Boards can be Nailed, Stuck Down, or Floated depending on product type and sub floor. Parquet woodblocks must be stuck down. All floors are Tongue and Groove with Ends Matched unless stated otherwise.
Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.
Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.
Nail Fitting: Nail fixing is usually done via a nail gun, e.g. Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.
Pre-Oiled: This product is supplied with a Factory UV Oiled surface. The Natural Wood Floor Company recommends that an additional coat of oil is applied to the surface prior to regular use.
Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.
Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.