Flooring 135 × 20 mm
The versatile nature of Oak means this floor is perfect for all kinds of design scheme. From more traditional, natural looking styles to more contemporary, coloured finishes, Oak can be tailored to your preference.
Engineered wood floors are suitable for laying over under floor heating and in kitchens, bathrooms, utility rooms, and any other room in the house because of their greater stability and lower moisture level in the wood.
The ply backing of an engineered floor with a hardwood veneer glued on top gives our engineered floors the same beautiful appearance of a solid wood floor but with more efficient use of precious hardwood.
The distinctive knots of our natural Oak give this floor a charming character that will bring a truly unique look to a home.
Unsealed products can be used to introduce a particular shade into a design scheme and are also ideal for colour-matching with an existing look.
Traditional boards are about 125 mm wide, so any floor with a width close to this will suit the proportions of older properties, especially those from the Victorian era.
Enter your details to calculate your meterage and cost.
Floor Size: 0m2
Extra Margin: 10%
Total Area Required:
This product can only be purchased in whole packs
Packs: Variable pack size
Our engineered board has been produced using WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.
The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.
Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The unsealed board is supplied with a micro bevel along the length of the board, pre- sanded requiring only a light 100/120 grit sand to finish.
Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production.
Product code: OLNU/135
Species: Oak
Finish: Unsealed
Brushed: No
Profile: Tongue and Groove
Specification: Bevelled Edge
Weight: 14.3 kg
Recommended Use: Domestic and Light Commercial
Dimensions: 135 × 20 mm
Width: 135 mm
Thickness: 20 mm
Colour : Natural
Type of finish : Unsealed
Under Floor Heating : Yes
Unit Measurement : per Square Metre
Design : 20mm Boards, Engineered
Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Birch Plywood. Boards can be Nailed, Stuck Down, or Floated depending on product type and sub floor. Parquet woodblocks must be stuck down. All floors are Tongue and Groove with Ends Matched unless stated otherwise.
Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.
Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.
Nail Fitting: Nail fixing is usually done via a nail gun, e.g. Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.
Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.
Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.